Black+Decker Washer E1 — What It Means & How to Fix It
Your Black+Decker washer didn't fill in time — E1 appears after about 30 minutes of filling without reaching the set level, nearly always a supply problem.
What this code means
E1 on a Black+Decker washer is the fill timeout: the manual flags it when filling runs past roughly 30 minutes without the water reaching the preset level. On these compact top-loaders the tap, faucet adapter, and inlet hose are the first things to check.
BLACK+DECKER's instruction manual for the BPWM09W 0.9 cu. ft. portable washer gives E1 as taking over 30 minutes to fill without reaching the preset water level. These washers are often fed through a faucet adapter, so a loose adapter or a tap not fully open is the usual reason. Other BLACK+DECKER washers may number their codes differently, so check the table in your own model's manual.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| Tap or faucet adapter not fully open | Very common | Yes — no tools |
| Kinked or trapped inlet hose | Common | Yes — no tools |
| Low water pressure at the tap | Common | Partly — check the tap |
| Clogged inlet mesh screen | Occasional | Yes — 10 min |
| Faulty inlet valve | Less common | No — technician job |
What you can try yourself
- Open the tap or faucet adapter all the way and check it's seated and sealed.
- Straighten the inlet hose and clear any kinks between the tap and the machine.
- Run the tap into a container to confirm it delivers a normal flow.
- Disconnect the hose and rinse the mesh screen at the inlet.
- Press Start/Pause, or unplug for a minute, to clear E1, then restart.
Seeing the symptom rather than the code? Washer not filling: checks that apply across brands.
When to call a technician
- The supply and hose are fine but the tub won't fill.
- Water only trickles in over a long time.
- The valve buzzes with little or no water entering.
Typical professional repair cost: Inlet valve replacement on a Black+Decker washer typically runs $80—$160 including labor.
Frequently asked questions
What does E1 mean on a Black+Decker washer?
It's the fill timeout — filling ran past about 30 minutes without reaching the set level. The cause is almost always the supply: a tap not fully open, a kinked hose, or low pressure.
How do I clear the E1 code?
Sort out the supply — open the tap or adapter, unkink the hose, clean the inlet screen — then press Start/Pause or unplug for a minute. E1 returns on the next fill if water still can't get in.
Could low pressure cause E1?
Yes. If the household supply is weak the washer may not reach its level within the 30-minute window. Test the tap into a bucket; poor flow there too points to the supply.
Sources checked
- BLACK+DECKER BPWM09W Portable Washer Instruction Manual, troubleshooting page (hosted by ManualsLib)
Error meanings can vary by model. This guide was checked against the documentation above; use the manual for the model number on your own appliance when it differs.
Related Black+Decker codes
- Black+Decker Washer E3 Your Black+Decker washer shows E3 when the spin has gone out of balance three times — open the lid, spread the wet load evenly and make sure the machine sits level.
- Black+Decker Washer E4 Your Black+Decker washer can't drain — E4 appears when draining takes over 10 minutes or the tub can't empty completely, usually a kinked or badly placed drain hose or a clogged filter.
- Black+Decker Washer E2 Your Black+Decker washer shows E2 when the top lid is open — close the lid fully and the cycle can carry on.
- Black+Decker Washer E5 Your Black+Decker washer shows E5 when the water has filled past its preset level — turn off the taps, and call the manufacturer's service line as the manual directs.
More: all Black+Decker washer codes · all Black+Decker codes · search by symptom