Frigidaire Washer E35 — What It Means & How to Fix It
Your Frigidaire front-load washer's water-level sensor is reporting more water than it should — either the tub really is overfilling from a stuck inlet valve, or the sensor is misreading; shut the taps and have it checked before running it.
What this code means
E35 trips when the pressure sensor detects water above the safe fill level. Sometimes that is real — an inlet valve stuck part-open keeps letting water in — and sometimes the sensor is faulty and crying overfill when the level is fine. Because a genuine overfill can flood, the safe first move is to cut the water supply; the actual repair is a technician's.
E35 is a digital-display front-load code on Frigidaire's Electrolux platform. If the machine is visibly overfilling, treat it as real and shut the taps; if the level looks normal, the sensor is the likelier culprit. Confirm against your model's manual.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| Water inlet valve stuck part-open, letting water keep entering | Common | Partly — shut taps, then technician |
| Faulty water-level pressure sensor misreporting the level | Common | No — technician job |
| Air-hose fault on the pressure sensor giving a false high reading | Occasional | Partly — inspect only |
| Control board fault | Less common | No — technician job |
What you can try yourself
- If you can see the tub overfilling, turn off both supply taps behind the washer right away to prevent a flood.
- Unplug the washer for five minutes, then restore power to clear any one-off sensor glitch.
- Restart and watch the fill: if water keeps coming with the machine paused, or it fills well past normal, the inlet valve is sticking — a technician's part.
- If the level actually looks normal but E35 still shows, the pressure sensor or its air hose is the likely fault; check that the air hose is seated, then call for service.
- Until it is diagnosed, leave the supply taps off between loads as a precaution.
When to call a technician
- Water keeps entering even when the cycle is paused or finished — shut the taps and call immediately.
- The washer overfills and trips the leak (E13) code as well.
- E35 persists after a reset with a normal-looking water level.
Typical professional repair cost: An inlet valve runs about $110–$210 with labor; a pressure-sensor repair is similar.
Frequently asked questions
Should I turn off the water if my Frigidaire shows E35?
Yes — if there is any sign of overfilling, shut the supply taps behind the machine first. A stuck inlet valve can keep filling and flood the floor, so cutting the water is the safe move while you arrange a repair.
Why would the sensor say overfill when the tub looks normal?
The water-level sensor reads pressure through a small air hose; a fault in the sensor or that hose can make it report a higher level than is really there. In that case nothing is actually overflowing, but the part still needs replacing.
Is E35 dangerous?
A genuine overfill can leak onto the floor, so it is worth treating seriously. Shutting the taps removes the flood risk; the electrical parts inside should only be handled by a technician.
Related Frigidaire codes
- Frigidaire Washer E11 Your Frigidaire front-load washer opened its fill valve but the water level didn't rise fast enough and timed out — almost always a restricted supply at the taps, hoses, or inlet screens rather than a dead valve.
- Frigidaire Washer E13 Your Frigidaire front-load washer has detected a leak — either water escaping the outer tub or, just as often, an air leak in the thin hose that lets the pressure sensor read the water level.
- Frigidaire Washer E20 Your Frigidaire front-load washer can't pump the water out, almost always because something is blocking the drain path — the pump filter, the drain hose, or the standpipe — rather than a failed pump.
- Frigidaire Washer E21 Your Frigidaire front-load washer is draining, but too slowly to satisfy the control within its time limit — usually a partial blockage in the pump filter or hose, or a drain pump that is losing strength.
More: all Frigidaire washer codes · all Frigidaire codes · search by symptom