Whirlpool Range F3 E0 — What It Means & How to Fix It
Also shown as F3E0 on some models.
F3 E0 on a Whirlpool-family range flags the oven temperature sensing circuit — Whirlpool's own description names the temperature sensor, the control, or the associated wiring. A one-minute breaker reset is the official first step.
What this code means
F3 E0 is a fault in the oven temperature sensing circuit. Whirlpool's product-help page for this code reads 'there may be a problem with the oven temperature sensor, the control, or the associated wiring' — the sensor at the back of the cavity, the board that reads it, or the wiring between them. Whirlpool's own resolution is a power reset: turn the unit off at the circuit breaker for one minute, restore power, monitor the oven for a minute to confirm the code doesn't return, then verify oven operation.
F3 E0 belongs to the F#E# platform shared by Whirlpool-family ranges (Whirlpool, KitchenAid, Maytag), and Whirlpool's product-help pages cover the family. The model number is on the frame behind the storage drawer or on the oven door frame.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| One-off reading after a power event | Very common | Yes — one-minute breaker reset |
| Oven temperature sensor failed | Common | No — technician job |
| Sensor connector or wiring fault | Occasional | Partly — inspect only |
| Control board misreading the circuit | Less common | No — technician job |
What you can try yourself
- Turn the unit off at the circuit breaker(s) for one full minute, then restore power — Whirlpool's own first and most common fix.
- Monitor the oven for one minute to make sure F3 E0 doesn't display again, then verify oven operation with a normal bake.
- If you can safely reach the sensor connector at the back of the cavity, check it is clean and fully seated.
- A recurring F3 E0 needs a technician to meter the sensor and trace the circuit — the part conversation starts only after the reset has failed.
When to call a technician
- F3 E0 returns after a clean one-minute breaker reset.
- The oven refuses to preheat, or heats erratically when it does run.
- The code alternates between F3 E0 and F3 E1 — a classic wiring signature on this platform.
Typical professional repair cost: No cost if the reset clears it; an oven temperature sensor replacement typically runs $120–$300 including labor, with control-board work on top at $200–$450.
Frequently asked questions
What actually is the 'oven temperature sensor'?
It's the probe in the back of the cavity that reports temperature to the control, which uses it to switch heating. When the reading is unreliable, the board shows F3 E0 rather than heat blindly.
Why does Whirlpool start with a breaker reset?
Because power dips and marginal connections can produce false sensor readings. Whirlpool's page for F3 E0 leads with exactly that: breaker off one minute, on, monitor one minute, then verify before anything else.
Is F3 E0 an electric-only or gas-range code?
It appears across the shared platform on both. The sensor circuit is common to gas and electric ovens — the reset and diagnosis path is the same; only the technician's access differs.
Sources checked
Error meanings can vary by model. This guide was checked against the documentation above; use the manual for the model number on your own appliance when it differs.
Related Whirlpool codes
- Whirlpool Range F3 E1 F3 E1 is the paired partner of F3 E0 on Whirlpool-family ranges: the same oven temperature sensing circuit, control, or wiring suspects, per Whirlpool's own page. A one-minute breaker reset is the official first step.
- Whirlpool Range F1 E0 F1 E0 on a Whirlpool-family range points at the oven control — Whirlpool's own page names the oven control or the associated wiring. A one-minute breaker reset is the official first step.
- Whirlpool Range F2 E0 F2 E0 on a Whirlpool-family range points at the user interface, the keypad, the control, or the wiring — the input side of the oven. Clean keys and a one-minute breaker reset first.
- Whirlpool Range F0 E0 F0 E0 appears when the electronic oven control cannot recognise what type of problem has occurred — turn the breaker off for one minute to reset it, and call for service if the code comes back.
More: all Whirlpool range codes · all Whirlpool codes · search by symptom