Midea Dishwasher E4 — What It Means & How to Fix It
Also shown as E8 on some models.
Your Midea dishwasher detected too much water or a leak — E4 is the anti-flood (overflow) trip, so the first move is to shut off the water and dry the base pan.
What this code means
E4 on a Midea dishwasher means the anti-flood system sensed water where it shouldn't be — usually a float in the base pan that rises when water collects there. It's a protective trip: the machine stops and often runs its pump to prevent a flood. Drying the pan resets the float, but a recurring E4 points to a real overfill or leak.
Some Midea models show this as E8. Excess detergent foam, a stuck inlet valve overfilling the tub, or a genuine leak can all raise the base-pan water. Anything beyond drying the pan and ruling out foam is a technician job, since it means finding a leak inside the machine.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| Water in the base pan tripping the float | Very common | Yes — dry the pan |
| Too much detergent / excess foam | Common | Yes — reduce soap |
| Inlet valve overfilling the tub | Occasional | No — technician job |
| Leak inside the machine | Occasional | No — technician job |
What you can try yourself
- Turn off the water supply to the dishwasher — the manual says to do this before calling for service if an overflow is showing.
- Unplug the unit, then tilt it gently or sponge out any water sitting in the base pan to reset the float.
- If you'd used too much detergent, run a rinse with little or no detergent to clear the foam.
- Restore power and run a short cycle; if E4 stays away, foam or a one-off overfill was the cause.
- If E4 returns, leave the water off and call a technician — a persistent trip means a leak or a stuck valve to find inside.
When to call a technician
- E4 returns after drying the base pan.
- You can see water pooling under or around the dishwasher.
- The tub overfills past its normal level.
Typical professional repair cost: Leak or inlet-valve repair on a Midea dishwasher typically runs $130—$300 including labor.
Frequently asked questions
What is the E4 (or E8) code on a Midea dishwasher?
It's the anti-flood trip — the machine sensed water in its base pan and stopped to prevent a flood. Drying the pan resets it, but if it returns there's a real overfill or leak to fix.
Is E4 safe to keep using?
Turn the water off first. The code is the machine protecting itself from a leak; running it again without finding the cause risks water on the floor. Dry the pan and test once, then call for service if it repeats.
Can too much detergent cause E4?
Yes — heavy foam can overflow and collect in the base pan, tripping the float. Use the recommended amount of dishwasher detergent and run a rinse to clear existing foam.
Related Midea codes
- Midea Dishwasher E1 Your Midea dishwasher didn't take in water within the allowed time — E1 is the fill (inlet) timeout, usually a closed tap, kinked hose, or clogged inlet screen.
- Midea Dishwasher E2 Your Midea dishwasher couldn't drain in time — E2 is the drain timeout, usually a clogged filter, kinked drain hose, or a disposer plug left in place.
- Midea Dishwasher E3 Your Midea dishwasher isn't reaching wash temperature — E3 is the heating fault, and because it sits on the heater circuit it's a technician repair after a single reset.
- Midea Washer E1 Your Midea washer isn't getting enough water during fill — E1 points to the supply side (taps, inlet hose, mesh filter) far more often than to the machine itself.
More: all Midea dishwasher codes · all Midea codes · search by symptom