Midea Washer E2 — What It Means & How to Fix It
Your Midea washer can't pump the water out — E2 flags a drain that didn't complete in time, usually a kinked or too-high drain hose or a clogged pump filter.
What this code means
E2 is the drain fault on a Midea washer: the pump ran but the tub didn't empty within the expected window. The machine stops before spin so it doesn't fling water around, which is why clothes are often left sitting in a pool when E2 appears.
Drain-hose height matters on these machines: if the hose loops too high or is pushed too far down a standpipe it can siphon or stall. Portable Midea models that drain into a sink hook are especially prone to a hose that has slipped or kinked.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| Kinked or flattened drain hose | Very common | Yes — no tools |
| Drain hose looped too high or pushed too far into the standpipe | Common | Yes — reposition |
| Clogged pump filter or trapped object | Common | Yes — towel, 15 min |
| Blocked standpipe or sink drain | Occasional | Partly — check the drain |
| Failed drain pump | Less common | No — technician job |
What you can try yourself
- Switch off and inspect the drain hose for kinks or crushing along its length.
- Make sure the hose outlet sits at the height the manual specifies and isn't jammed deep into the standpipe, which causes siphoning.
- If your model has an access panel at the lower front, lay a towel down and clean the pump filter and remove anything trapped.
- Pour water down the standpipe or sink drain to confirm the house side isn't backed up.
- Clear E2 (Start/Pause or a brief power-off) and run a Spin/Drain to retest.
When to call a technician
- The hose and filter are clear but water still won't leave the tub.
- The pump hums without moving water, or stays silent.
- Water backs up out of the standpipe or sink — a drain problem, not the washer.
Typical professional repair cost: Drain pump replacement on a Midea washer typically runs $110—$230 including labor.
Frequently asked questions
Why is there still water in my Midea washer with E2?
E2 means the pump couldn't clear the water in time, so the machine halts with the tub still full. Clear the hose and pump filter, then run a drain/spin — the water leaves once the blockage is gone.
How high should the Midea drain hose be?
Follow the height in your model's manual — too high and the pump can't lift the water, too far down a standpipe and it siphons. Many portable models are designed to hook over a sink edge at a set height.
Can a small sock cause E2?
Yes. A sock, coin, or hairpin that gets past the tub can lodge in the pump or filter and choke the drain. Cleaning the pump filter clears most of these on models that have an accessible trap.
Related Midea codes
- Midea Washer E1 Your Midea washer isn't getting enough water during fill — E1 points to the supply side (taps, inlet hose, mesh filter) far more often than to the machine itself.
- Midea Washer E3 Your Midea washer doesn't think the lid is shut — E3 is the lid/lid-switch fault, so the machine won't spin until it's satisfied the lid is closed.
- Midea Washer E4 Your Midea washer found the load lopsided during spin — E4 is the out-of-balance fault, cleared by spreading the laundry evenly and levelling the machine.
- Midea Dishwasher E1 Your Midea dishwasher didn't take in water within the allowed time — E1 is the fill (inlet) timeout, usually a closed tap, kinked hose, or clogged inlet screen.
More: all Midea washer codes · all Midea codes · search by symptom