Comfee Washer E1 — What It Means & How to Fix It
Your Comfee washer isn't filling — E1 is the water-inlet fault, usually a faucet adapter that's loose or half-open, a kinked hose, or a clogged inlet screen.
What this code means
E1 on a Comfee washer means water didn't reach the set level in time. Comfee is one of Midea's compact-appliance brands, and on its portable and small top-load washers the fill relies on a tap or faucet adapter — so the supply connection is the first thing to check.
Comfee's owner's manual for the CLV09N1AMG and CLV09N1AWW lists E1 as taking over 30 minutes to fill without reaching the preset water level. Most Comfee washers fill from a single cold inlet via an adapter that clips to a kitchen or bathroom faucet, so a poor adapter seal or a tap not opened fully is the usual reason. Other Comfee washers may number their codes differently, so check the table in your own model's manual.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| Faucet adapter loose or tap not fully open | Very common | Yes — no tools |
| Kinked or trapped inlet hose | Common | Yes — no tools |
| Clogged mesh screen at the inlet | Common | Yes — 10 min |
| Low water pressure at the tap | Occasional | Partly — check the tap |
| Faulty inlet valve | Less common | No — technician job |
What you can try yourself
- Check the faucet adapter is seated and the tap is open all the way.
- Straighten the inlet hose and remove any kinks between the tap and the machine.
- Disconnect the hose and rinse the small mesh screen at the inlet where sediment collects.
- Confirm the tap itself runs at a normal rate into a container.
- Press Start/Pause (or unplug for a minute) to clear E1, then restart.
Seeing the symptom rather than the code? Washer not filling: checks that apply across brands.
When to call a technician
- The adapter and hose are fine but the tub won't fill.
- Water trickles in far too slowly.
- The valve buzzes with no water entering.
Typical professional repair cost: Inlet valve replacement on a Comfee washer typically runs $80—$160 including labor; on a portable unit it can be less.
Frequently asked questions
Why does my Comfee portable washer show E1?
It isn't getting water fast enough. On portable Comfee washers that's almost always the faucet adapter being loose or the tap not fully open — check the connection first, then the hose and inlet screen.
How do I reset the E1 code?
Sort out the supply (adapter, tap, hose, screen), then press Start/Pause or unplug the washer for a minute. E1 reappears on the next fill if the water still can't get in.
Do I need both hot and cold for a Comfee washer?
Most compact Comfee models use a single cold inlet, so you only connect one supply. Check your model — if it has two inlets, both need to be open.
Sources checked
Error meanings can vary by model. This guide was checked against the documentation above; use the manual for the model number on your own appliance when it differs.
Related Comfee codes
- Comfee Washer E2 Your Comfee washer thinks the top lid is open — E2 is the lid code, and the fix the manual gives is simply to close the lid.
- Comfee Washer E3 Your Comfee washer can't balance the load for spin — E3 is the out-of-balance fault, fixed by spreading the laundry evenly and levelling the machine.
- Comfee Washer E4 Your Comfee washer can't pump out the water — E4 is the drain fault, usually a kinked drain hose, a hose draped too high, or a clogged filter.
- Comfee Washer E5 Your Comfee washer shows E5 when the water has filled past its preset level — turn off the faucet, and call the service center as the manual directs.
More: all Comfee washer codes · all Comfee codes · search by symptom