Comfee Washer E2 — What It Means & How to Fix It
Your Comfee washer thinks the top lid is open — E2 is the lid code, and the fix the manual gives is simply to close the lid.
What this code means
E2 on a Comfee portable washer is the open-lid code: the manual's entry reads "The top lid is open", with "Close the lid" as the solution. The washer needs the lid shut before it will carry on, so clothing caught over the rim or a lid that hasn't dropped fully home is enough to raise it.
Comfee's owner's manual for the CLV09N1AMG and CLV09N1AWW lists E2 as the top lid being open. On that model a drain fault is E4, not E2. Other Comfee washers may number their codes differently, so check the table in your own model's manual.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| Lid left open or not fully closed | Very common | Yes — no tools |
| Laundry or an object caught under the lid rim | Common | Yes — no tools |
| Lid opened part-way through a cycle | Common | Yes — close and restart |
| Failed lid switch | Less common | No — technician job |
What you can try yourself
- Close the lid and press it down until it sits flat all the way round.
- Check the rim for a sleeve, strap or detergent cap holding the lid up, and clear it.
- Press Start/Pause to carry on with the cycle.
- If E2 stays, unplug the washer for a minute, plug it back in and try again with the lid shut.
- If E2 still shows with the lid clearly closed, stop there — the lid switch needs a technician.
Seeing the symptom rather than the code? Washer door or lid trouble: checks that apply across brands.
When to call a technician
- E2 stays on with the lid fully closed and nothing caught under it.
- The lid or its hinge is cracked or no longer sits flat.
- The code comes and goes when the lid is touched during a cycle.
Typical professional repair cost: Usually $0 — closing the lid clears it. Replacing a failed lid switch on a Comfee washer typically runs $90—$180 including labor.
Frequently asked questions
What does E2 mean on a Comfee washer?
On the CLV09N1AMG and CLV09N1AWW it means the top lid is open. Close the lid fully and press Start/Pause; the cycle carries on once the washer sees the lid shut.
Why does my Comfee washer show E2 when the lid is closed?
Something may be holding the lid slightly up — fabric over the rim is the usual culprit. If the lid sits flat and E2 remains after a one-minute unplug, the lid switch itself is the likely fault.
Is E2 a drain error on a Comfee washer?
Not on the CLV09N1 models: their manual lists the drain fault as E4 and the open lid as E2. Numbering can differ on other Comfee washers, so check the code table for your model.
Sources checked
Error meanings can vary by model. This guide was checked against the documentation above; use the manual for the model number on your own appliance when it differs.
Related Comfee codes
- Comfee Washer E1 Your Comfee washer isn't filling — E1 is the water-inlet fault, usually a faucet adapter that's loose or half-open, a kinked hose, or a clogged inlet screen.
- Comfee Washer E3 Your Comfee washer can't balance the load for spin — E3 is the out-of-balance fault, fixed by spreading the laundry evenly and levelling the machine.
- Comfee Washer E4 Your Comfee washer can't pump out the water — E4 is the drain fault, usually a kinked drain hose, a hose draped too high, or a clogged filter.
- Comfee Washer E5 Your Comfee washer shows E5 when the water has filled past its preset level — turn off the faucet, and call the service center as the manual directs.
More: all Comfee washer codes · all Comfee codes · search by symptom