Maytag Range F2 E0 — What It Means & How to Fix It
Also shown as F2E0 on some models.
F2 E0 on a Maytag range points at the user interface, the keypad, the control, or the wiring — the input side of the oven. Clean keys and a one-minute breaker reset first.
What this code means
F2 E0 is an input-side fault on the F#E# platform Maytag ranges share with the Whirlpool family. The platform's official page reads 'there may be a problem with the user interface or keypad, the control, or the associated wiring' — a stuck or wet key, a failing keypad board, or the harness feeding the control. The resolution is the standard power reset: breaker off one minute, restore, monitor one minute, verify oven operation.
F2 E0 is part of the F#E# platform, and the shared official page defines it as the user interface/keypad, the control, or their wiring. The model number is on the frame behind the storage drawer.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| Stuck or moisture-bridged key on the keypad | Very common | Yes — clean and dry the keys |
| User interface/keypad board failed | Common | No — technician job |
| Keypad-to-control harness or connector fault | Occasional | No — technician job |
| Control board misreading the keypad | Less common | No — technician job |
What you can try yourself
- Wipe the keypad clean and dry, pressing every key once to work them free — a sticky or wet key is the most common F2 E0 source.
- Turn the unit off at the circuit breaker(s) for one full minute, restore power, and monitor for one minute to confirm the code doesn't return.
- Press each key individually and confirm the display responds — a key that registers itself points straight at the keypad.
- If F2 E0 persists after cleaning and a reset, the keypad, its harness, or the control needs a technician's diagnosis.
When to call a technician
- F2 E0 returns after the keypad is clean and dry and the breaker was cycled.
- The oven enters keys by itself, including when nothing is touched.
- The whole control goes unresponsive alongside the code.
Typical professional repair cost: No cost if cleaning and a reset cure it; keypad replacement typically runs $120–$300 including labor, and the display/control board runs $200–$450.
Frequently asked questions
Why does moisture trigger F2 E0?
Touch panels read tiny electrical changes — a wet or greasy film can read like a finger held down, and the control calls that a fault. A dry, clean keypad clears the largest share of F2 E0.
Is F2 E0 an oven problem or an input problem?
Input. The platform's own wording puts the user interface and keypad first, then the control and wiring. The reset handles the power-event version; persistent codes are an input-surface or harness repair.
Can I still use the surface burners with F2 E0 showing?
Usually the cooktop works independently, but the code means the control can't trust its input. Clear it with the reset, and treat a returning F2 E0 as reason to have the keypad checked before long.
Sources checked
Error meanings can vary by model. This guide was checked against the documentation above; use the manual for the model number on your own appliance when it differs.
Related Maytag codes
- Maytag Range F3 E0 F3 E0 on a Maytag range flags the oven temperature sensing circuit — the shared-platform documentation names the temperature sensor, the control, or the associated wiring. One-minute breaker reset first.
- Maytag Range F3 E1 F3 E1 is the paired partner of F3 E0 on Maytag's shared platform: the same oven temperature sensing circuit, control, or wiring suspects. A one-minute breaker reset is the official first step.
- Maytag Range F1 E0 F1 E0 on a Maytag range points at the oven control — the shared platform's name for it is the oven control or the associated wiring. One-minute breaker reset first.
- Maytag Dryer PF PF on a Maytag dryer is the power-failure notice: the dryer lost power mid-cycle and stopped. Nothing is broken — clear the code and resume the load.
More: all Maytag range codes · all Maytag codes · search by symptom