Maytag Range F3 E1 — What It Means & How to Fix It
Also shown as F3E1 on some models.
F3 E1 is the paired partner of F3 E0 on Maytag's shared platform: the same oven temperature sensing circuit, control, or wiring suspects. A one-minute breaker reset is the official first step.
What this code means
F3 E1 is a fault in the oven temperature sensing circuit — the shared-platform documentation for F3 E1 reads the same as its F3 E0 page: 'there may be a problem with the oven temperature sensor, the control, or the associated wiring.' The two codes are the paired readings of that circuit; which one you see depends on the model and what the board last sensed. The resolution is identical: breaker off one minute, restore power, monitor one minute, verify oven operation.
The platform's product-help pages for F3 E0 and F3 E1 carry the same sensor/control/wiring wording, which is how the F#E# system treats the pair. Maytag ranges share that platform with the Whirlpool family. The model number is on the frame behind the storage drawer.
Most likely causes
| Cause | How likely | DIY-fixable? |
|---|---|---|
| One-off reading after a power event | Very common | Yes — one-minute breaker reset |
| Oven temperature sensor failed | Common | No — technician job |
| Sensor connector or wiring fault | Occasional | Partly — inspect only |
| Control board misreading the circuit | Less common | No — technician job |
What you can try yourself
- Turn the unit off at the circuit breaker(s) for one full minute, then restore power — the same official reset the platform gives for the F3 pair.
- Monitor the oven for one minute to confirm F3 E1 doesn't return, then verify oven operation.
- Check the sensor connector at the back of the cavity only if you can safely reach it — it should be clean and fully seated.
- If F3 E1 persists, a technician meters the sensor and traces the circuit; either digit of the pair points at the same parts.
When to call a technician
- F3 E1 returns after a clean one-minute breaker reset.
- The oven refuses to preheat, or heats erratically.
- F3 E0 and F3 E1 trade places on the display — a chafed-wiring signature needing a professional look.
Typical professional repair cost: No cost if the reset clears it; an oven temperature sensor replacement typically runs $120–$300 including labor, with control-board work on top at $200–$450.
Frequently asked questions
What's the difference between F3 E0 and F3 E1?
They're the two readings of the same temperature sensing circuit — which one displays depends on the model and what the board last sensed. The platform's documentation describes both with identical sensor/control/wiring wording.
Do I treat F3 E1 differently from F3 E0?
No — same reset, same checks, same suspects. Whether your display shows E0 or E1, the path is the same until a technician meters the circuit.
Can I keep cooking with F3 E1 showing?
The oven may hold heat, but without reliable temperature data it can misbehave. Clear the code with the reset; if it returns, use the oven cautiously until a technician checks the circuit.
Sources checked
Error meanings can vary by model. This guide was checked against the documentation above; use the manual for the model number on your own appliance when it differs.
Related Maytag codes
- Maytag Range F3 E0 F3 E0 on a Maytag range flags the oven temperature sensing circuit — the shared-platform documentation names the temperature sensor, the control, or the associated wiring. One-minute breaker reset first.
- Maytag Range F1 E0 F1 E0 on a Maytag range points at the oven control — the shared platform's name for it is the oven control or the associated wiring. One-minute breaker reset first.
- Maytag Range F2 E0 F2 E0 on a Maytag range points at the user interface, the keypad, the control, or the wiring — the input side of the oven. Clean keys and a one-minute breaker reset first.
- Maytag Dryer PF PF on a Maytag dryer is the power-failure notice: the dryer lost power mid-cycle and stopped. Nothing is broken — clear the code and resume the load.
More: all Maytag range codes · all Maytag codes · search by symptom